Hughes HN7700S User Manual Page 112
- Page / 140
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Appendix D • Conformance with standards and directives
98
1037753-0001 Revision A
Company will provide advance notice in order for you to make
the necessary modifications to maintain uninterrupted service.
Repairs in the United States
If trouble is experienced with the Two-Way Hughes System
equipment, for repair or warranty information, contact your
service provider.
If the equipment is causing harm to the telephone network, the
Telephone Company may request that you disconnect the
equipment until the problem is resolved.
Hughes must make any necessary repairs to the modem portion of
this equipment in order to maintain valid FCC registration. Do
not attempt to repair or service your router. Return it to Hughes.
No repairs can be made by customers. All repairs must be done
by a Hughes authorized service center. This equipment cannot be
used on public coin service provided by the Telephone Company.
Connection to Party Line Service is subject to state tariffs.
Contact the state public utility commission, public service
commission or corporate commission for information.
Canada – equipment
attachment limitations
The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain
telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal
Equipment Technical Requirement Documents. The Department
does not guarantee the equipment will operate to the user's
satisfaction.
Before installing this equipment, users should make sure they are
permitted to connect to the facilities of the local
Telecommunications Company. The equipment must also be
installed using an acceptable method of connection. In some
cases, the company's inside wiring associated with a single line
individual service may be extended by means of a certified
connector assembly (telephone extension cord). The customer
should be aware that compliance with the above conditions might
not prevent degradation of service in some situations.
Note: This equipment meets the applicable Industry Canada
Terminal Equipment Technical Specifications. This is confirmed
by the registration number. The abbreviation IC before the
registration number signifies that registration was performed based
on a Declaration of Conformity indicating that Industry Canada
technical specifications were met. It does not imply that Industry
Canada approved the equipment.
- HN System 1
- Revision record 2
- Important safety information 3
- Contents 5
- • Contents 6
- Chapter 5 9
- Chapter 6 10
- Chapter 7 10
- Chapter 8 10
- Appendix A 10
- Appendix B 11
- Appendix E 11
- Appendix F 12
- Chapter 1 13
- Chapter 3 13
- • Tables 14
- Introduction 15
- Router specifications 16
- Commissioning 17
- Associated transport 17
- Installation and 18
- Contact information 18
- Chapter 2 19
- G-29716 C 05/19/08 20
- Customer site 21
- Attaching the base 24
- Removing the base 24
- Connecting an AC/DC power 26
- Connecting a DC/DC power 27
- Chapter 4 29
- LEDs on power-up 31
- LED Pattern Description 32
- Commissioning the HN router 33
- Changing from VSAT to 34
- Figure 9: Setup screen 35
- Terrestrial Broadband 36
- Setup page 36
- Figure 12 37
- Commissioning by auto 38
- Figure 15 39
- 6. Click Next 41
- Figure 18 41
- Entering and verifying 42
- Completing the 44
- Connecting the HN 45
- Commissioning by 47
- Entering and verifying the 48
- 11. Click Next 49
- Verifying the download 52
- Figure 30: SDL Monitor page 53
- Completing the process 54
- System Control Center 55
- Figure 33: Settings screen 56
- Accessing the System 57
- Control Center 57
- The System Control 57
- Center home page 57
- System Status button 59
- The System Status page 60
- LAN Info page 61
- Figure 41: LAN Info page 62
- WAN Info page 63
- System Info page 64
- Additional Home Page 65
- System Status 65
- Diagnostic Utilities 65
- Help page 66
- Help page links 67
- Advanced Pages 68
- Accessing the 69
- Expanding and collapsing 70
- Requirements for VADB 72
- Installing VADB 72
- Verifying that the VADB 73
- Testing the telephone line 74
- Connecting the HN router 75
- Optional protection module 76
- T0155016 77
- Verifying VADB functionality 78
- LED appearance during 79
- VADB operation 79
- VADB troubleshooting 80
- Windows XP 86
- Windows 2000 89
- Updating the router software 91
- Configuring TCP/IP 92
- Updating the 100
- Troubleshooting 101
- 1037753-0001 Revision A 102
- Appendix C 103
- Netscape 105
- Appendix D 107
- Safety – operating 108
- Electromagnetic 109
- Telecommunications 110
- Ringer equivalence number 111
- Discontinuance of service 111
- Telephone Company 111
- Repairs in the United States 112
- Canada – equipment 112
- ADTRAN Total Access 600R 113
- Installing the ADTRAN 114
- Figure 85: LED positions 115
- Supplying power 116
- ADTRAN front panel 116
- Navigating the user 117
- Navigating using 119
- Connecting the 120
- Configuring the 121
- 5. Select the + sign 122
- Figure 96 125
- DS0 mapping 126
- 7. Press Enter 127
- Confirming connectivity 129
- Siemens 4100/4101 DSL Modem 131
- Installation overview 132
- Installing the modem 133
- 3. Click the Install button 134
- Figure 106 134
- Figure 107 135
- Figure 108 135
- Acronyms and abbreviations 137
- • Acronyms and abbreviations 138
- • Index 139
Related products and manuals for Networking Hughes HN7700S
(68 pages)© 2020, manymanuals.com. All rights reserved. | 0.540 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals